JVC GD-V501PCE Manuale Utente

PLASMA DISPLAY MONITORINSTRUCTIONSGD-V501PCE

10ConnectionsPC Input Terminals connectionNotes:(1) Computer signals which can be input are those with a horizontal scanning frequency of 15.5 to 110

11SERIAL Terminals connectionConnectionsNotes:(1) Use the RS-232C cable to connect the computer to the Plasma Display.(2) The computer shown is for ex

12Basic ControlsR - STANDBYG POWER ONINPUT– VOL +Volume AdjustmentPress the Volume Up “+”or Down “–” button toincrease or decrease thesound v

13OFF TIMER buttonThe Plasma Display can be preset to switch to stand-byafter a fixed period. The setting changes to 30 minutes,60 minutes, 90 minutes

14Power On/Off and input signal selectionPower On/OffRemote Control SensorR - STANDBYG POWER ONINPUT— VOL +R - STANDBYG POWER ONPower Indic

15Select the input signalR - STANDBYG POWER ONINPUT— VOL +— VOL +INPUTPress the INPUT button to select the inputsignal to be played bac

16PLASMA DISPLAYINPUTSURROUNDVOLNRPICTURESOUNDSET UPASPECTPICTUREPOS. /SIZEOFF TIMERPCPictureNormalisePicture ModeBrightnessColourNormal00TintWhite ba

17On-Screen Menu Display from Remote ControlNote:“Signal” setup menu displays different setting condition for each input signals. (see page 15)To Sign

18ASPECT ControlsThe Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinemaformat picture.PLASMA

19ASPECT ControlsMode4 : 3Zoom16 : 9JustAutoExplanation4:3 will display a 4:3 picture at its standard 4:3 size.Zoom mode magnifies the central section

2Table of ContentsBasic Controls... 12Power On/Off and input signal selection ... 14AC

20Adjusting Picture Pos./SizePLASMA DISPLAYN RINPUTSURROUNDVOLPICTURESOUNDSET UPASPECTPICTUREPOS. /SIZEOFF TIMERPCAdjusting screen1PICTUREPOS. /SIZEPr

21Adjusting Picture Pos./SizeH-PosH-SizeV-PosV-SizeClock Phase(RGB/PC in Mode)When the Position Right “ ” button is pressed.When the Position Right “

22SoundNormaliseSound ModeBassTrebleNormalOn000BalanceSurroundNormalSound Adjustment12Press to display the Sound menu.Select to adjust each item.Press

23Surround ControlsSURROUND ButtonThe benefits of surround sound are enormous. You can becompletely enveloped in sound; just as if you were at a conce

24Press the left or right button toselect “On”. Press the down button toenter Advanced Settings mode.Advanced Settings OnEnables fine picture ad

25Note:In PICTURE, there is not a noticeable change even when contrast is increased with a bright picture or reduced with adark picture.Picture Adjust

26Set up TIMERThe timer can switch the Plasma Display On or Off.Before attempting Timer Set, confirm the PRESENT TIME and adjust if necessary.Then set

27TIMER SetSet up TIMERPRESENT TIMEPOWER ON Function0:52OffPOWER ON TimePOWER OFF FunctionPOWER OFF Time0:000:00OffPress to display the POWER ON Setup

28Screensaver (For preventing after-images)Do not display a still picture, especially in 4:3 mode, for any length of time.If the display must remain o

29Off Low Mid High RScreensaverFunctionModeWhite bar scrollTime DesignationStart Time0:000:00SP AdjustmentMidFinish Ti

3Trademark Credits• VGA is a trademark of International Business Machines Corporation.• Macintosh is a registered trademark of Apple Computer, USA.• S

30Setup for Input SignalsComponent/RGB-in SelectSelect the input signals to be connected by installing the Optional Video Input Card.(Refer to the ser

31Set up TIMERSetupSignalScreensaverComponent/RGB-in selectRGBOSD LanguageEnglish (UK)3D Y/C Filter (NTSC)Colour system3:2 PulldownOnAutoOffAspe

32Select Signal from the “Setup” menu during RGB or PC input signal mode.Press to adjust.SyncH & VSyncon VIDEOSyncon GSetting RGB sync signal:Co

33TroubleshootingBefore you call for service, determine the symptoms and make a few simple checks as shown below.SymptomsSome parts of the screendo no

34ConnectionsSERIALPC INAUDIOPR/CR/RPB/CB/B Y/GCOMPONENT/RGB INAVVDHDRLS VIDEOINVIDEOOUTVIDEOINAUDIOINRLAUDIOCOMPONENT/RGB IN and Audio IN Termina

35Luminance earthLuminance inChrominance earthChrominance inS VIDEO 4 pin socket (S VIDEO VCR)S VIDEOVideo input toS VIDEOsocketAudio input toL/R soc

36(VCR)AV2Video input toBNC socketAudio input toL/R sockets(DVD / Satellite Receiver)AV1/TVVideo input toBNC socketRCA-BNCadapter plugAudio input toL/

37ConnectionsComponent/RGB Input connectionNotes:(1) Change the “Component/RGB-in” setting in the “Setup” menu to “Component”. (see page 30)(2) Additi

38SpecificationsGD-V501PCE220 - 240 V AC, 50Hz/60Hz 495 W 3.0 W 1.7 WDrive method AC type50-inch, 16:9 aspect ratio3000:11,106 mm (W) × 622 mm (H)

39SpecificationsNotes:(1) Design and specifications are subject to change without notice. Weight and dimensions shown are approximate.(2) This equipme

4Important Safety NoticeIMPORTANT: THE MOULDED PLUGFOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.This appliance is supplied with a moulded

GD-V501PCE PLASMA DISPLAY MONITORVICTOR COMPANY OF JAPAN, LIMITED© 2003 VICTOR COMPANY OF JAPAN, LIMITEDPrinted in JapanTQZW243

5Safety PrecautionsWARNINGSetupThis Plasma Display is for use only with the following optional accessories. Use with any other type of optionalaccesso

6Safety PrecautionsIf problems occur during useIf a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come o

7GD-V501PCEPLASMA DISPLAYINPUTSURROUNDVOLNRPICTURESOUNDSET UPASPECTPICTUREPOS. /SIZEOFF TIMERPCAccessoriesOptional AccessoriesAccessories SupplyCheck

8Remote Control BatteriesRequires two R6 batteries.1. Turn the transmitter face down.Press and slide off the batterycover.2. Install the batteries as

9ConnectionsSERIALPC INAUDIOTo tighten:To loosen:Pushthe catchPullPull121212SPEAKERSTerminals (R)SPEAKERSTerminals (L)– Cable fixing bandsSecure an